You should read the entire instruction manual prior to proceeding with your installation.<\/strong><\/p>\n It is important to familiarize yourself with the ModdBox Supercharger Kit installation.\u00a0 It is the responsibility of the installer to properly install the Supercharger Kit.\u00a0 To ensure safety and proper installation, ModdBox recommends that this product only be installed by a qualified professional with access to pneumatic tools and a strong familiarity with automotive service procedures.<\/p>\n Tuning is not covered in this manual.<\/strong><\/p>\n Moddbox is an automotive parts supplier only and tuning services are not offered. \u00a0However, Moddbox provides customer support for your parts installation and can provide guidance regarding tuning options. \u00a0In addition,\u00a0Lasota Racing provides online tuner services to many of our customers. \u00a0For more information about Lasota Racing’s online tuning services, visit our Lasota Racing – Online Tuning Manual<\/a> here.<\/p>\n<\/div>\n EGR \u2013 Exhaust Gas Recirculation<\/p>\n HVAC \u2013 Heating Ventilation & Air Conditioning<\/p>\n IAC \u2013 Idle Air Control<\/p>\n MAF \u2013 Mass Air Flow<\/p>\n TPS \u2013 Throttle Position Sensor<\/p>\n Vac – Vacuum<\/p>\n Standard metric socket set<\/span><\/p>\n Hex key set<\/p>\n Various pliers<\/p>\n T-30 Torx bit<\/p>\n Fluid funnel<\/p>\n Oil pan<\/p>\n Flat head screw driver<\/p>\n Pneumatic or electric hammer drill<\/p>\n Crescent wrench<\/p>\n Utility knife<\/p>\n Shop vacuum<\/p>\n Rat tail file<\/p>\n Propane torch or similar heating device<\/p>\n Wire Strippers<\/p>\n Wire Crimper<\/p>\n Stock Intake Pipe & Air Box Reference Diagram<\/p>\n Stock Exhaust Gas Re-circulation (EGR) Reference Diagram<\/p>\n Throttle & Stock Intake Manifold Reference Diagram<\/p>\n Ignition Coil Reference Diagram<\/p>\n Belt Diagram Reference Diagram (Dark Belt Showing the ModdBox Orientation)<\/p>\n Only key components in the kit are shown here. \u00a0Refer to the parts list provided with your product for a complete list of product components.<\/p>\n<\/div>\n ModdBox Supercharger Bypass Valve<\/p>\n <\/p>\n ModdBox 5.5.0 & 8.0\u00a0psi Supercharger Pulleys<\/p>\n ModdBox Quick Change Pulley Adapter<\/p>\n ModdBox Plenum Bottom Plate<\/p>\n ModdBox Plenum Top Plate<\/p>\n ModdBox Intake Manifold<\/p>\n ModdBox Intake Manifold Top<\/p>\n ModdBox Stainless EGR Extension<\/p>\n Black Silicone Liquid Gasket<\/p>\n Moddbox 6PK Serpentine Belt<\/p>\n SUPERCHARGER INSTALLATION (5-6 hours)<\/p>\n Disconnect TPS plug and Electronic Throttle Plug.<\/p>\n Disconnect MAF plug.<\/p>\n Disconnect Crank Case Vent hose from the Intake Hose.<\/p>\n Disconnect EGR plug and EGR vac line. \u00a0Remove the EGR valve and set aside for future use.<\/p>\n Disconnect Spark Plug Wires\u00a0and remove the\u00a0Plug Wire Retaining Clip from the top of the Stock Intake Manifold. \u00a0Disconnect the Vac Line and Fuel Vapor Return Line as shown. \u00a0Mark them with tape if necessary.<\/p>\n Disconnect Electrical Plug Mount from Stock Intake Manifold. \u00a0Use the supplied short plastic straps to secure this to your wiring harness or fuel rail as required.<\/p>\n Disconnect the passenger side Crank Case Ventilation Tube.<\/p>\n Remove the two bolts shown. \u00a0This will disconnect your Stock Intake Manifold from your Ignition Coil Mounting Bracket.<\/p>\n Disconnect the plug to your Ignition Coil.<\/p>\n Pry your Ignition Coil assembly toward the Driver Side (the assembly should be displaced by approximately 2-2.5″ to allow for the future relocation of your EGR valve).<\/p>\n Remove the Stock Rubber Intake Tube and set it aside for future use.<\/p>\n Disconnect the Throttle body. \u00a0You may want to loosen the Coolant Line Retaining Clips to allow the coolant lines to twist on their mount points. \u00a0Place the Throttle Body aside for future use.<\/p>\n Use a\u00a0T-30 Torx bit and remove the eight bolts that connect the Stock Intake Manifold to the Engine Block. \u00a0The bolt locations are shown below:<\/p>\n Clean and vacuum the area if necessary.\u00a0 Be sure to clean the Engine Block\u2019s mating faces. \u00a0Caution:\u00a0 Do not drop anything into the Intake Ports.\u00a0 Before Proceeding, fill the Intake Ports with rags or paper towel.<\/i><\/strong><\/p>\n Place a bead of RTV Black Liquid Gasket around the engine’s inlet ports as shown.<\/p>\n Obtain the Moddbox Lower Plenum and fit the Future Intercooler Inlet\/Outlet ports with the provided NPT plugs. \u00a0Place a bead of RTV Black Liquid Gasket around the ports openings as shown.<\/p>\n Optional:<\/i><\/strong>\u00a0 If you have purchased a ModdBox IAT\/ACT relocation kit, install the provided IAT\/ACT sensor and wire harness to the red highlighted location as shown below. \u00a0Connect two wires to the harness using and route them to the front of the vehicle towards the MAF. \u00a0Refer to the IAT\/ACT relocation instructions for further information.<\/p>\n Optional:<\/i><\/strong>\u00a0 If you have purchased a ModdBox Intercooler Kit, replace the provided NPT plugs highlighted green below with the provided NPT hose fittings. \u00a0Refer to the ModdBox Intercooler Kit Installation Manual for further instructions.<\/p>\n <\/p>\n Caution: The Plenum Base Plate is NOT reversible.<\/i><\/strong>\u00a0 Before placing the Plenum Base Plate on the Engine Block, note the orientation of the lower plenum. \u00a0The front of the lower plenum has a bulge as shown in the picture below. \u00a0Torque the provided M6x35 SHCSs to 13lbft. \u00a0Start at the center bolts and work your way to the ends in a cross-pattern.<\/p>\n Remove the stock alternator shield.<\/p>\n Remove the Coolant Cap. \u00a0Locate the plastic Radiator Drain Valve at the bottom passenger side of the Radiator.\u00a0 Turn this plug and release approximately a gallon of coolant fluid (~4L).<\/p>\n Remove the Stock Upper Radiator hose and set it aside for future use. \u00a0Remove the Thermostat Coolant Elbow and replace it with the one provided as shown. \u00a0Be sure to clean the mating flanges and replace the o-ring. \u00a0Failure to do so may result in a\u00a0coolant\u00a0leak.<\/p>\n Replace the Stock Upper Radiator hose with the one supplied. \u00a0The Throttle Body Coolant Hoses will need to be re-arranged as shown.<\/p>\n Obtain the Moddbox Intake Manifold and install the brass fittings as shown (2x 1\/4″ NPT Plugs and 2x 1\/4″-3\/8″ Barbs). \u00a0 Use the hardware and RTV Black Liquid Gasket to securely bolt the supplied block plates as shown. \u00a0Install the Supercharger Bypass Valve as shown. \u00a0The NPT Plug shown below is for an optional Future Methanol Injection Port.<\/p>\n Optional:<\/i><\/strong>\u00a0 If you plan to install a methanol injection kit, it is advisable to install the methanol injection nozzle at this time.<\/p>\n Connect the 14″ long 3\/8″ hose to the 3\/8″ Barb as illustrated below. \u00a0Secure it with one of the provided stainless hose clamps. \u00a0Leave the other end loose until a later step.<\/p>\n <\/p>\n Obtain your Eaton M90 Supercharger \u00a0(either an 89-93 oval or 94-95 rectangular style\u00a0M90)\u00a0and the provided ModdBox\u00a0Stainless Steel Supercharger Pulley Adapter. \u00a0Remove the supercharger’s flange bolt and ensure the shaft key is inserted and aligned.<\/p>\n Use a propane torch to pre-heat the Stainless Steel Pulley Adapter (allowing it to thermally expand). \u00a0Slip the supercharger Adapter onto your supercharger shaft until it binds. \u00a0Note: \u00a0The pulley is designed to have an interference fit which will cause the pulley to jam once it slips halfway onto the shaft. \u00a0<\/em>If you do not have a torch, simply placing the adapter in a cup of boiling water should expand the adapter enough to proceed.<\/em><\/p>\n If you did not use a torch, the threads of the supercharger shaft might not be exposed. \u00a0Use a hammer and a socket and gently tap<\/span> the Adapter further down the shaft until the first few threads on the supercharger shaft are exposed beyond the Stainless Adapter bore as shown below.<\/p>\n Utilize the stock Eaton M90 Supercharger Lock Nut and two box wrenches. \u00a0Use one wrench to prevent the Adapter from rotating \u00a0(utilizing the flats on the stainless steel part) and use the other wrench to apply torque on the Supercharger Lock Nut. \u00a0Continue to torque down the nut until the back of the Adapter hits the stop on the Supercharger shaft. \u00a0Caution: Be sure that no debris falls into your Eaton M90 Supercharger.\u00a0 The tolerances on your supercharger is only ~0.003″-0.007″\u00a0and can be damaged if material gets sucked into the supercharger housing. \u00a0Rotating the rotors by hand can generate enough air flow to suck debris into the rotors.\u00a0 Use a vacuum to clear your rotors prior to installation.<\/i><\/strong><\/p>\n Obtain the provided ModdBox 6PK Custom Pulley and slip it onto the Supercharger Pulley Adapter. \u00a0\u00a0Caution<\/em>: \u00a0The pulley is a machined precision slip-fit (only when both parts are room temperature). \u00a0You must either heat the Pulley or wait for the Adapter to cool prior to slipping it on. \u00a0No force should be required. \u00a0The pulley will not bind if it is slipped on straight.<\/em><\/strong><\/p>\n Rotate the pulley and align the\u00a0\u00a0M5 threads with the pulley holes (should rotate freely if slipped on correctly). \u00a0Torque down the provided M5x16mm socket head cap screws.<\/p>\n Obtain the Moddbox Plenum Top Plate. \u00a0Install the 1\/8″ NPT and 1\/4″ NPT Brass Plugs as shown. \u00a0These plugs have been provided for the use of optional intake temperature and boost senors\/controllers. \u00a0Apply a bead of the RTV Black Liquid Gasket to the Moddbox Plenum Top Plate\u00a0flange as illustrated.<\/p>\n Optional:<\/i><\/strong>\u00a0 If you plan to install a\u00a0boost gauge or intake temperature sensor, it is advisable to install them at this time.<\/p>\n Obtain the ModdBox Plenum Top Plate and bolt it to the base of the Eaton M90 Supercharger & Pulley Assembly. Use the provided M8x40mm socket head cap screws.\u00a0 Clean any excess gasket material.<\/p>\n Obtain the Stock Upper Radiator Hose that was previously set aside. \u00a0Measure out and cut a length of hose as is required for your supercharger:<\/p>\n For the 94\u2019-95\u2019 Eaton M90 Supercharger (rectangular inlet):\u00a0\u00a01-7\/8\u201d<\/strong><\/p>\n For the 89\u2019-93\u2019 Eaton M90 Supercharger (oval inlet):\u00a0\u00a02-5\/8\u201d<\/strong><\/p>\n Use one of the 2\u201d stainless hose clamps to secure the hose to the Plenum Top Plate.\u00a0 Loosely place the other 2\u201d diameter stainless hose clamp on the hose.<\/p>\n Use the RTV Black Liquid Gasket and put a thin bead on both the Supercharger and the Moddbox Intake Manifold. \u00a0Press the Moddbox Intake Manifold Assembly onto the hose prepared in a previous step.<\/p>\n Bolt the Moddbox Intake Manifold to the back of the Supercharger using the provided four M8x25 SHCS\u00a0bolts. \u00a0Use the RTV Black Liquid Gasket to seal the Moddbox Custom Washer in place as shown (the bolt located inside the Intake Manifold). \u00a0Tighten the 2″ stainless hose clamp around the bypass valve.<\/p>\n Note: \u00a0The Moddbox Custom Washer must be reversed for the 94-95 Superchargers (orientation shown is for the 89-93 superchargers).<\/em><\/p>\n Use the RTV Black Liquid Gasket and place a bead around the Intake Manifold Top Flange. \u00a0Place and bolt-up the Intake Manifold Cover as shown. \u00a0This whole Supercharger Assembly will be used in the next steps.<\/p>\n Remove the rags or paper towels in your Engine Inlet Ports.\u00a0 Apply a thin bead of Black Liquid Gasket along the Plenum Base Plate.\u00a0\u00a0Caution:\u00a0 Be sure to apply gasket material around all the bolt holes (as illustrated in the photo below). The gasket material must be extended to the inside edge of the mating face as shown on the bottom-left of the photo below. Failure to do so can result in a leak in your Intake Manifold Assembly.<\/strong><\/i><\/p>\n (Note:\u00a0 Engine rags\/paper towels removed from engine ports prior to installing Plenum Top Plate)<\/i><\/p>\n Place the whole Supercharger Assembly on the Moddbox Plenum Bottom Plate. \u00a0Align the holes and bolt it down using the twelve M8x30 hex bolts. \u00a0Do not forget the bolt under the Supercharger Snout. \u00a0Torque the bolts in a cross-pattern.<\/p>\n Locate the disconnected Fuel Vapor Return Line.\u00a0 Cut off the press fit connection and reconnect it to the remaining 3\/8\u201d barb on the ModdBox Intake Manifold.<\/p>\n Connect the fuel Vapor Return Line to the un-used Barb as illustrated.<\/p>\n Use the provided 1\/4″ Tee and connect the Brake Boost and Vac Lines to the 14″ long 3\/8″ diameter hose connected to the Supercharger Assembly (prepared in an earlier step). \u00a0Secure the Vac lines with the provided hose clamps.<\/p>\n Connect the Moddbox Flexible EGR Extension to your EGR valve.<\/p>\n Caution: \u00a0The Stainless Steel EGR Extension is not designed to be twisted. \u00a0Do not twist the EGR Extension when tightening the threads or damage to the extension may occur.\u00a0<\/strong><\/p>\n Install the EGR Valve using the Moddbox EGR Spacer and the provided M8x40 SHCS bolts. \u00a0Note: \u00a0The provided\u00a0spacer is anodized black (raw aluminium shown).<\/em><\/p>\n Install the Throttle Body.<\/p>\n Bend the Stainless Steel EGR Extension to suit. \u00a0Secure it with the provided C-clamps as shown. \u00a0Connect the EGR Extension to the stock EGR re-circulation line.<\/p>\n Use a knife and carefully cut your Stock Rubber Intake Pipe along the center of the ribs as shown. \u00a0Be sure to count the ribs and confirm the exact location for cutting.<\/p>\n Use your knife and carefully carve out the ribs to allow for a stainless hose clamp.<\/p>\n Install the Moddbox Intake Pipes using the Stock Rubber Intake pieces and the provided hose clamps.<\/p>\n Install the 5\/8″ diameter hose to the Crankcase vents as shown connecting the PCV valve (from passenger-side crank case cover) to the Moddbox Intake Manifold’s brass 90degree elbow fitting (at bottom behind supercharger). \u00a0Connect the driver-side open crank case vent to the intake pipe immediately downstream of the air filter. \u00a0Use the provided elbow and stainless steel hose clamps to securely fasten them together.<\/p>\n Use the provided wire and butt crimps to extend your Electronic Throttle, TPS, and EGR plugs. \u00a0Use the loom and remaining plastic strap to secure and clean-up the wiring once completed. \u00a0Plug the wires back into the TPS and EGR.<\/p>\n Slack your Belt Tensioner using a 3\/8\u201d Box Wrench or Belt Removal Tool.\u00a0 Remove the Stock belt and replace it with the ModdBox 6PK Belt as illustrated below.<\/p>\n <\/p>\n Plug in the MAF sensor, reconnect the disconnected Ignition wires, top up the coolant level, and reconnect the battery. \u00a0The last step required is to wait 24 hours. \u00a0You must allow the liquid gasket material to fully cure at room temperature or as per the manufacturer’s recommendations. \u00a0Failure to provide the necessary curing time may lead to vacuum leaks.<\/p>\n MAF sensor plug<\/p>\n EGR Vac Line to EGR Valve<\/p>\n EGR Stainless Recirculation Line (if equipped)<\/p>\n Crank Case Vent Hose to Intake Tube (may be 2 depending on your model)<\/p>\n IAC Electrical Plug (may need to check polarity on the wiring extension)<\/p>\n TPS Electrical Plug\u00a0(may need to check polarity on the wiring extension)<\/p>\n Electronic Throttle Plug<\/p>\n Ignition Coil Plug<\/p>\n Fuel Vapor Return Line<\/p>\n Fuel Injection Vacuum Line<\/p>\n Brake Booster Vacuum Line<\/p>\n \u00a0<\/span><\/p>\n Running the 3.15″ diameter pulley (max 5.5psi)<\/strong><\/p>\n At minimum, you will require the installation of larger injectors (suggest 39+lb\/hr), colder plugs (suggest 1 heat range colder with 0.035″ gap – ex NGK TR6GP), higher octane fuel, and an ecu remap. \u00a0We also recommend upgrading your fuel pump to a high flow 255lph (optional), installing cooling equipment such as a methanol injection kit or intercooler (optional), and scaling your MAF to avoid pegging (optional). \u00a0Moddbox assists customers with tuning by suggesting an online tune shop,\u00a0Lasota Racing<\/a>. \u00a0We also sell an\u00a0SCT firewire to PLX module cable and a compatible A\/F Module & Gauge Combo Package that makes tuning easy. \u00a0For more information, please contact us at info@modd.me.<\/p>\n Running the 2.9″ or 2.64″ diameter pulley<\/strong><\/p>\n When using the 2.9″ or 2.64″ diameter pulleys, you will exceed the 5V limit of your stock MAF sensor. \u00a0You will be required to scale your MAF (using a product like the DiabloMAFia or similar) or upgrade it to high flow MAF. \u00a0Talk to your tuner for more information.<\/p>\n Starting Your Vehicle for the First Time\u00a0<\/strong><\/p>\n Caution: \u00a0Be sure you have waited 24hrs for your liquid gasket material to fully cure prior to proceeding. \u00a0<\/strong><\/em><\/p>\n If you are unsure about whether you have correctly installed everything described in this manual, please spend some time to review the instructions and consult the “connection check list”.<\/p>\n Once the checklist has been consulted… \u00a0it’s time to turn the key \ud83d\ude42 \u00a0 Your vehicle should start up exactly as it did before. \u00a0It may however turn over once before starting if the fuel lines where not fully primed. \u00a0If your vehicle idles rough, you have probably missed a vacuum line. \u00a0Consult the installation steps above.<\/p>\n Tuning is the most important component of ensuring you get the most out of your Moddbox Supercharger Installation Kit. \u00a0Shopping around for a qualified tuner that has experience with Mustangs is highly recommended.<\/p>\n Making sure your vehicle does not run lean is very important. \u00a0Installing an optional Air to Fuel (AFR or A\/R) gauge with a wideband oxygen sensor is recommended. \u00a0As a rule of thumb, an AFR while in boost and running premium street fuel of 11.5 is optimum. \u00a0Having a gauge is great way to monitor the operation of your supercharged engine.<\/p>\n As discussed, we recommend either installing either Methanol Injection or an Intercooler Kit for all boosts above 3.0 psi. Forced induction adds heat to the intake air as a result of compression. \u00a0This added heat can increase your exhaust gas temperatures (EGTs) during extremely harsh driving conditions. \u00a0These EGTs could adversely affect your vehicle. \u00a0This risk can be mitigated by installing cooling equipment (intercooler or methanol injection). \u00a0You can also mitigate this risk by installing an EGT gauge and keeping the temperatures below 1500 degF. \u00a0As a rule of thumb, never go over 1600 degF.<\/p>\n Idle is Erratic<\/b><\/p>\n<\/div>\n If your idle rises and falls in a repeating pattern, you have a massive Vacuum leak. \u00a0One of the items on the connection list was likely missed.<\/p>\n Vehicle\u00a0makes a whistle sound when driving<\/b><\/p>\n You probably have a kink in your crank case ventilation hose or a vacuum leak.<\/p>\n Squealing Pulley<\/strong><\/p>\n The removal and replacement of a new belt may have caused your worn idler pulley to start squealing. \u00a0Apply lubrication or replace your idler pulley.<\/p>\n Thank you for choosing Moddbox! \u00a0We would love to hear how we can make this installation manual better. \u00a0If you feel we could improve it\u00a0in any way, please let us know by emailing us at info@modd.me.<\/p>\n Submit your build photos! \u00a0We love seeing your builds. \u00a0Please submit your Name, State\/Province, and some photos of your vehicle and we will add you to our customer build section.<\/p>\n<\/div>\n<\/div>\n","protected":false},"excerpt":{"rendered":" The following Installation Instructions apply to the\u00a02005-2010 Ford Mustang\u00a04.0L SOHC models (also very similar to the 2005-2010 Ford Explorers with the exception of initial disassembly).\u00a0Prior to proceeding, confirm that your engine bay looks similar to the following photo: You should read the entire instruction manual prior to proceeding with your installation. It is important… View Article<\/a>","protected":false},"author":1,"featured_media":3210,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[53],"tags":[73,74,75,76,77,78,29,79,80,61,81,58],"class_list":["post-3087","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-howtos","tag-73","tag-74","tag-75","tag-76","tag-77","tag-78","tag-4-0","tag-4-0l","tag-kit","tag-moddbox","tag-mustang","tag-supercharger"],"_links":{"self":[{"href":"https:\/\/kelowna.website\/4\/wp-json\/wp\/v2\/posts\/3087","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/kelowna.website\/4\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/kelowna.website\/4\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/kelowna.website\/4\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/kelowna.website\/4\/wp-json\/wp\/v2\/comments?post=3087"}],"version-history":[{"count":0,"href":"https:\/\/kelowna.website\/4\/wp-json\/wp\/v2\/posts\/3087\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/kelowna.website\/4\/wp-json\/wp\/v2\/media\/3210"}],"wp:attachment":[{"href":"https:\/\/kelowna.website\/4\/wp-json\/wp\/v2\/media?parent=3087"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/kelowna.website\/4\/wp-json\/wp\/v2\/categories?post=3087"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/kelowna.website\/4\/wp-json\/wp\/v2\/tags?post=3087"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}![\"d0b3b37a-d795-43b9-b3a2-63ebdc0bae4a\"](\"http:\/\/modd.me\/wp-content\/uploads\/2014\/04\/d0b3b37a-d795-43b9-b3a2-63ebdc0bae4a.jpg\")
<\/a><\/p>\nREFERENCE ABBREVIATIONS<\/h3>\n<\/div>\n
TOOLS REQUIRED<\/h3>\n<\/div>\n
STOCK REFERENCE DIAGRAMS<\/h3>\n
<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\nMODDBOX SUPERCHARGER KIT PARTS<\/h3>\n
<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\nINSTALLATION STEPS<\/h3>\n<\/div>\n
<\/a><\/p>\n<\/a><\/p>\n<\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/p>\n<\/a><\/p>\n<\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/p>\n<\/a><\/em><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\nCONNECTION CHECK LIST<\/h3>\n
INITIAL DRIVING & TUNING INSTRUCTIONS<\/h3>\n<\/div>\n
RECOMMENDATIONS<\/h3>\n<\/div>\n
TROUBLESHOOTING COMMON PROBLEMS<\/h3>\n<\/div>\n
<\/a><\/p>\n<\/a><\/p>\n